Accessories

Power, store and maintain your Moticon products.

Accessories

Power, store and maintain your Moticon products.

Connectivity.

Accessories enabling connectivity of your Moticon Sensor Insoles.

ANT USB dongle

The ANT USB dongle connects the Moticon Sensor Insoles wirelessly to the computer. The wireless connection is used to control the sensor insole as well as for streaming or downloading measurement data in Live mode.

The dongle plugs into Windows PCs and to Apple Mac computers.

  • USB connector:  Type A
  • Frequency: 2400 MHz
  • Transfer rate: up to 20 kbps
  • Dimensions: 61 x 18 x 8.6 mm

Download datasheet

The ANT USB songle is a mandatory accessory for all Moticon Software products for desktop computers since it is also used for verifying the Moticon Software license codes.

Note: Although the dongle is a third provider product, it cannot be purchased from alternative suppliers since the Moticon Software license matching does not work then.

USB download cable

The USB download cable is only needed for SCIENCE Pro Sensor Insoles!

It is used for downloading measurement data from the Sensor Insoles that was stored on-board. The download speed is increased significantly compared to wireless download.

  • USB connector:  Type A
  • Transfer rate: ~ 46 Kbps (true data throughput)
  • Download time: ~ 12 min. complete memory 1 pair of Sensor Insoles
  • Example: 1h measurement @50Hz takes 1 minute to download

The cable fits into the battery compartment of the Sensor Insoles and establishes a data link as the 2 pins of the cable plugs connect to the battery lid inside the Sensor Insole.

Power supply.

Essentials you need for powering and charging your Moticon Sensor Insoles.

Rechargeable coin cell

Moticon Sensor Insoles are powered with rechargeable Li-Ion coin cells – one per Sensor Insole. We offer and recommend special high performance coin cells from our partner Route Jade from South Korea. Those coin cells display a higher capacity than other products on the market.

  • Type and form factor: PD2032
  • Technology: Li-Ion coin cell
  • Voltage: 3.7 V (nominal)
  • Capacity: 85 mAh (nominal)
  • Capacity after 500 charge cycles: 56 mAh (66 %)

The coin cell fits into the battery compartment at the bottom side of all Moticon Sensor Insoles. They go “+” pole outside underneath the battery flap and are covered with a special plastic battery lid.

Attention: The use of standard primary coin cells (e.g. CR2032) will lead to malfunction!

Coin cell charger

This coin cell charger is an original Moticon equipment, designed to perfectly match charging requirements for PD2032 coin cells. The charger ensures optimal charging curves and 100 % charge status at the end of the charge cycle.

In order to achieve top performance for longterm measurements with Moticon Sensor Insoles, we strongly recommend to use the dedicated Moticon coin cell charger.

  • 2 charging slots for PD2032 rechargeable coin cells
  • Battery status LED: power on, charging, ready (for each slot)
  • Reset button
  • Charge time: ~ 2 h (full charge cycle, PC2032 coin cell)
  • Charge voltage: 4.2 V
  • USB connector: Micro-USB B (“smartphone” type, wall adapter not included!)
  • Dimensions: 46 x 34 x 23 mm

The coin cell charger can be connected to a wall adapter delivery USB voltage with a Micro-USB B connector. Alternatively, it can be connected to any device delivering USB voltage with a Type A to Micro-USB B cable.

Product bags.

Handy and slim product bags exlusively manufactured for protecting your Moticon products on the go or when you store them.

Product bag

The handy product bag features a variety of compartments and protects your Moticon products. We strongly recommend to use the product bag in order to avoid damage of valuable product components.

The bag is exlusively manufactured for Moticon and strongly recommended for your convenience in daily work.

 

  • 6 compartments for one pair of Sensor Insoles each
  • 2 flat zipper compartments for cables, battery bag or other accessories
  • 1 big side compartment for coin cell charger and other accessories
  • Carrying handle and adjustable shoulder strap
  • Material: Cordura
  • Form factor: 430 x 300 x 60 mm

The compartments for sensor insoles can be fixed with a velcro fastener. All other compartments are equipped with zippers for safe storage of items.

Coin cell bag

The coin cell bag is the fuel tank for your Moticon Sensor Insoles. It stores coin cells in a handy zipper protected and wallet style way. Searching for batteries and mixing up charged and empty ones belong to the past.

The bag is exlusively manufactured for Moticon and strongly recommended for you convenience in daily work.

  • Stores coin cells for 10 pairs of Sensor Insoles
  • 20 compartments for 2032 coin cells
  • Flat, zipper protected package
  • Material: Cordura and rubber band
  • Form factor: 150 x 90 x 15 mm

No special usage requirements.

Sensor Insole bag

The Sensor Insole bag makes it easy to store Sensor Insoles when you just take along one pair. It has a tie strap to close it safely and fits all Sensor Insole sizes.

  • Fits all Sensor Insole sizes
  • Tie strap for closure

No special usage requirements.

Spare parts.

Some items you may need to exchange or just needed as spare parts.

Battery lid

Just in case one of your battery lids gets lost: we offer the item as a spare part in order to keep you productive. The battery lid fits all Moticon Sensor Insole models and comes in pairs.

 

  • Fits all Moticon Sensor Insole models
  • Suitable for Moticon battery compartments housing PD2032 coin cells

No special usage recommendations.

Connectivity.

Accessories enabling connectivity of your Moticon Sensor Insoles.

ANT USB dongle

The ANT USB dongle connects the Moticon Sensor Insoles wirelessly to the computer. The wireless connection is used to control the sensor insole as well as for streaming or downloading measurement data in Live mode.

The dongle plugs into Windows PCs and to Apple Mac computers.

  • USB connector:  Type A
  • Frequency: 2400 MHz
  • Transfer rate: up to 20 kbps
  • Dimensions: 61 x 18 x 8.6 mm

Download datasheet

The ANT USB songle is a mandatory accessory for all Moticon Software products for desktop computers since it is also used for verifying the Moticon Software license codes.

Note: Although the dongle is a third provider product, it cannot be purchased from alternative suppliers since the Moticon Software license matching does not work then.

USB download cable

The USB download cable is only needed for SCIENCE Pro Sensor Insoles!

It is used for downloading measurement data from the Sensor Insoles that was stored on-board. The download speed is increased significantly compared to wireless download.

  • USB connector:  Type A
  • Transfer rate: ~ 46 Kbps (true data throughput)
  • Download time: ~ 12 min. complete memory 1 pair of Sensor Insoles
  • Example: 1h measurement @50Hz takes 1 minute to download

The cable fits into the battery compartment of the Sensor Insoles and establishes a data link as the 2 pins of the cable plugs connect to the battery lid inside the Sensor Insole.

Power supply.

Essentials you need for powering and charging your Moticon Sensor Insoles.

Rechargeable coin cell

Moticon Sensor Insoles are powered with rechargeable Li-Ion coin cells – one per Sensor Insole. We offer and recommend special high performance coin cells from our partner Route Jade from South Korea. Those coin cells display a higher capacity than other products on the market.

  • Type and form factor: PD2032
  • Technology: Li-Ion coin cell
  • Voltage: 3.7 V (nominal)
  • Capacity: 85 mAh (nominal)
  • Capacity after 500 charge cycles: 56 mAh (66 %)

The coin cell fits into the battery compartment at the bottom side of all Moticon Sensor Insoles. They go “+” pole outside underneath the battery flap and are covered with a special plastic battery lid.

Attention: The use of standard primary coin cells (e.g. CR2032) will lead to malfunction!

Coin cell charger

This coin cell charger is an original Moticon equipment, designed to perfectly match charging requirements for PD2032 coin cells. The charger ensures optimal charging curves and 100 % charge status at the end of the charge cycle.

In order to achieve top performance for longterm measurements with Moticon Sensor Insoles, we strongly recommend to use the dedicated Moticon coin cell charger.

  • 2 charging slots for PD2032 rechargeable coin cells
  • Battery status LED: power on, charging, ready (for each slot)
  • Reset button
  • Charge time: ~ 2 h (full charge cycle, PC2032 coin cell)
  • Charge voltage: 4.2 V
  • USB connector: Micro-USB B (“smartphone” type, wall adapter not included!)
  • Dimensions: 46 x 34 x 23 mm

The coin cell charger can be connected to a wall adapter delivery USB voltage with a Micro-USB B connector. Alternatively, it can be connected to any device delivering USB voltage with a Type A to Micro-USB B cable.

Product bags.

Handy and slim product bags exlusively manufactured for protecting your Moticon products on the go or when you store them.

Product bag

The handy product bag features a variety of compartments and protects your Moticon products. We strongly recommend to use the product bag in order to avoid damage of valuable product components.

The bag is exlusively manufactured for Moticon and strongly recommended for you convenience in daily work.

 

  • 6 compartments for one pair of Sensor Insoles each
  • 2 flat zipper compartments for cables, battery bag or other accessories
  • 1 big side compartment for coinc cell charger and other accessories
  • Carrying handle and adjustable shoulder strap
  • Material: Cordura
  • Form factor: 430 x 300 x 60 mm

The compartments for sensor insoles can be fixed with a velcro fastener. All other compartments are equipped with zippers for safe storage of items.

Coin cell bag

The coin cell bag is the fuel tank for your Moticon Sensor Insoles. It stores coin cells in a handy zipper protected and wallet style way. Searching for batteries and mixing up charged and empty ones belong to the past.

The bag is exlusively manufactured for Moticon and strongly recommended for you convenience in daily work.

  • Stores coin cells for 10 pairs of Sensor Insoles
  • 20 compartments for 2032 coin cells
  • Flat, zipper protected package
  • Material: Cordura and rubber band
  • Form factor: 150 x 90 x 15 mm

No special usage requirements.

Sensor Insole bag

The Sensor Insole bag makes it easy to story Sensor Insole when you just take along one pair. It has a tie strap to close it safely and fits all Sensor Insole sizes.

  • Fits all Sensor Insole sizes
  • Tie strap for closure

No special usage requirements.

Spare parts.

Some items you may need to exchange or just needed as spare parts.

Battery lid

Just in case one of your battery lids gets lost: we offer the item as a spare part in order to keep you productive. The battery lid fits all Moticon Sensor Insole models and comes in pairs.

 

  • Fits all Moticon Sensor Insole models
  • Suitable for Moticon battery compartments housing PD2032 coin cells

No special usage recommendations.

Contact

Moticon GmbH
Machtlfinger Str. 21
81379 Munich, Germany

Contact us
Service Hotline

+49 89 2000 301 50
Mo-Fri 9:00 am to 6:00 pm (UTC+1)
Follow Us